ROBOTICS & AUTOMATION

Custom Robotics
Cable Assemblies

Connect your robot.
Define the motion.

Build-to-print power, feedback, sensor and control harnesses for robotics OEMs and automation integrators. Manufactured to your approved drawings, components and inspection requirements.

Discuss Your Robotics Project

Illustrative robot arm with an external cable bundle routed around its joints in an automation cell

From controller to end effector.

PowerFeedbackSignalControl

ONE ROBOT. DIFFERENT CONNECTIONS.

Specify each circuit.
Review the complete route.

A robotics cable assembly connects the robot’s electrical components with specified cable, connectors, terminations and protection. A wire harness can combine several branches into one organized installation.

The right configuration depends on where it runs, what it carries and how it moves.

Explore custom wire harnesses

Motor & actuator power
Define voltage, current, conductor size, protective earth where required, and the mating drive or actuator interface.
Encoder & feedback
Confirm circuit assignments, connector orientation, shielding and the feedback system’s cable specification.
Sensors & end effectors
Route I/O, gripper, tool and sensor connections around mounting points, service access and tool changes.
Controllers & communication
Connect boards, panels and network interfaces to the specified pinout. Data rate and protocol performance need their own acceptance criteria.

START WITH THE MOVEMENT

Fixed. Bending. Twisting.
Different demands on the cable.

Describe the motion before selecting the construction. A cable that bends easily by hand is not automatically suitable for continuous flexing or robot torsion.

Keep the installed geometry under control.

For wiring within a controller, robot base or stationary machine section, define the installation bend radius, clearances, fastening points and service loop.

  • Installed bend radius and available space
  • Mounting, vibration and connector retention
  • Heat, abrasion and environmental exposure

Add this motion type to my enquiry

Use the cable supplier’s limits for the selected part number. Confirm the assembly and routing in the actual motion profile; no universal bend radius, torsion angle or cycle life is assumed.

ASSEMBLY OPTIONS

Build around the interfaces.

Choose the circuit layout, connector system and protection together. The examples below show available assembly structures.

Multi-branch harnesses

Integrate sensor, I/O and control branches with defined breakout positions, lengths, labels and connector cavities.

Custom harness architecture ↗

Signal & control assemblies

Specified board, panel and device interfaces, with circuit verification and shield termination where required.

Signal & control harnesses ↗

Molded connector exits

Review cable-exit direction, jacket compatibility and strain relief against the connector, tooling and installation.

Overmolded interfaces ↗

THE ROBOTICS RFQ

Turn the operating conditions
into a build specification.

Include the drawing revision and exact component references. Flag open questions so the quotation identifies what still needs approval.

Requirement Information to provide Review focus
Electrical load Voltage, current per circuit, conductor size, grounding and equipment interfaces. Wire, contact and connector compatibility; specified insulation and termination requirements.
Motion profile Bending or torsion, travel, speed, acceleration, duty cycle and required service life. Cable construction, supplier motion ratings and the agreed application validation plan.
Routing & dimensions Overall and branch lengths, tolerances, bend clearances, fixing points and connector clocking. Assembly fit, slack, strain relief, tool access and separation from moving parts.
Signal & shielding Interface specification, pair assignment, shield continuity and grounding arrangement. Shield preparation, termination and test criteria. EMC or network performance requires defined validation.
Environment Temperature, abrasion, vibration, oil, coolant, cleaning agents and required sealing. Selected jacket, sleeves, connectors and molded transitions; exposure-specific evidence.
Acceptance & records Inspection methods, limits, sampling, identification, revision and required documentation. Manufacturing checks, first-article approval and any additional qualification arrangements.

Connector brands identify specified components. Confirm exact part numbers, mating parts and the approved sourcing route.

Illustrative robotics routing concept

FROM DRAWING TO REPEAT BUILD

Prove the configuration.
Then release production.

  1. 01

    Review the build

    Check the BOM, pinout, motion route, component availability and inspection requirements before agreeing the manufacturing route.

  2. 02

    Make & review the first article

    Prepare and terminate wires, assemble the connectors, route branches and apply specified protection. Review fit and agreed inspection results.

  3. 03

    Approve & repeat

    Resolve changes, freeze the revision and document the approved configuration for pilot or repeat production.

Prototype-to-production support ↗

INSPECTION & VALIDATION

Check the assembly.
Validate the application.

Manufacturing inspection verifies the approved build. Robot motion, service life and equipment performance need a defined qualification plan.

Electrical & circuit checks

Agree the connection map, continuity and wire-sequence checks. Define DC resistance or other electrical tests where required.

Termination & dimensions

Review crimp pull-force or cross-section checks as appropriate, contact seating, connector orientation, branch lengths and markings.

Motion & system validation

Set the bend radius, torsion, speed, load, environment and failure criteria for any flex-life test. Confirm the test arrangement before committing to a performance claim.

ENGINEERING & SOURCING QUESTIONS

Before you send
the drawing.

Answers for a clearer robotics cable assembly RFQ.

What information do you need for a robotics cable quotation?

Send the drawing, BOM, connector and terminal part numbers, pinout, dimensions, quantity and inspection criteria. For moving routes, add the motion profile, installed bend radius, torsion angle over free cable length, environment and validation requirements.

Can a drag-chain cable be used on a rotating robot joint?

Do not assume it can. Repeated bending and multi-axis torsion place different demands on cable construction. Check the selected part’s ratings for the actual motion and confirm the installed routing and test conditions.

Can you guarantee a particular number of flex cycles?

A cycle-life commitment requires a defined cable, termination, route, bend radius, torsion, speed, temperature and failure criterion, supported by applicable test evidence. This page does not state a universal flex-cycle rating.

Can you use our specified servo, encoder or sensor connectors?

Send the exact housing, contact, seal and mating-interface references for review. Confirm cable compatibility, keying, pin assignment and clocking. Brand names or connector appearance alone are insufficient.

Do you support industrial Ethernet or other communication cables?

Specified communication assemblies can be reviewed against the cable and connector system. Identify the protocol, cable category, pair map, shielding and acceptance tests. Bandwidth or protocol certification is not inferred from a completed continuity test.

Does overmolding make a robotics harness waterproof?

Overmolding can provide strain relief and protection. A sealing claim depends on the complete connector, cable exit, materials, mating condition and agreed ingress test. Define the target before choosing the construction.

Can you build prototypes before repeat production?

Prototype and pilot requirements can be reviewed before production release. Component availability, tooling, first-article inspection and customer approval determine the build plan, minimum quantity and lead time.

Can a cable assembly establish the robot’s safety compliance?

No. Manufacture to an approved wiring specification does not establish functional safety or equipment-level compliance. The robot or machine manufacturer must define safety-related requirements, validation and system release.

LET’S REVIEW YOUR CONNECTIONS

Bring the drawing.
Include the movement.

Share the available specifications and identify what still needs to be defined. We’ll review the components, manufacturing route and inspection scope.

Useful project inputs

Drawing & BOM · Pinout · Cable and connector references · Route and branch lengths · Motion profile · Environment · Quantity · Acceptance criteria

info@xsdharness.com ↗






    One file up to 10 MB. Combine multiple documents in a ZIP file.