Custom FFC
Cable Assemblies

XSD Harness provides custom flat flexible cable assemblies for compact electronic and display interconnections. Assemblies are built to customer-defined pitch, conductor count, cable length, contact orientation, connector requirements, routing, and inspection criteria.

Illustration of thin laminated FFC cables with flat exposed contacts and blue reinforcement

What Is an FFC Cable Assembly?

A flat flexible cable, or FFC, uses parallel flat conductors laminated within a thin flexible insulation system. Its low-profile construction makes it suitable for compact electrical connections between PCBs, displays, control boards, and electronic modules where space and routing height are limited.

A custom FFC assembly can be defined by pitch, conductor count, overall length, exposed contact length, contact orientation, reinforcement, connector interface, fold pattern, and project-specific electrical or mechanical requirements.

FFC vs Ribbon Cable vs FPC

Product Construction Main characteristic Typical use
FFC Flat parallel conductors laminated in flexible insulation Thin, compact, low profile Board, display, compact electronics
Ribbon Cable Multiple insulated round conductors arranged side by side Organized multi-wire routing IDC and general electronic interconnects
FPC Printed copper circuit traces on flexible substrate Routed circuit patterns Complex compact electronic circuits

Customer-specified FPC components can be reviewed for integration. FPC circuit fabrication is separate from FFC assembly capability.

Explore Ribbon Cable Assemblies

Custom FFC Cable Assembly Configurations

Select a configuration for review against your drawing, mating interface and intended application. Availability is confirmed for the specified construction.

Straight FFC Cables

Low-profile, direct PCB-to-PCB or module connections with defined cable length and contact exposure.

Same-Side Contact FFC

Contacts exposed on the same face at both ends, matched to the connector contact positions.

Opposite-Side Contact FFC

Contacts exposed on opposite faces where the two mating interfaces require a reversed contact orientation.

Folded FFC Assemblies

Specified folds for constrained internal routing, with fold location and bend requirements documented.

FFC with Connector Integration

Customer-specified connector housings or interface components integrated where the cable system permits.

Overmolded / Reinforced FFC Assemblies

Selected strain-relief or protective processing, subject to material, tooling and design compatibility.

FFC Contact Orientation Options

Same-side contacts are often called Type A or same-face contacts. Opposite-side contacts may be called Type B or reverse-side contacts. Supplier terminology varies.

Same-side contacts: both exposed contacts face upward in this side-view schematicEnd AEnd BSame faceExposed contactStiffener on reverse face

Side-view schematic · thickness exaggerated for clarity

Contact orientation should always be confirmed by drawing or connector interface rather than relying only on Type A/Type B terminology.

FFC Pitch & Conductor Count

FFC pitch and conductor count depend on cable construction, the mating connector, current requirements, routing constraints and product design. Confirm both against the connector and approved drawing.

Pitch is the center-to-center spacing between adjacent conductors. Conductor count and cable width are related, but width alone does not define the mating interface.

FFC drawing showing pitch between adjacent conductor centers, conductor count, exposed contact length, reverse-face stiffener and overall lengthOverall lengthExposed contact lengthPitchConductorcountStiffener (reverse)Top-view schematic · dimensions specified by drawing

Custom FFC Cable Assembly Options

Specify the cable and the finished interface together. Reinforcement thickness, contact exposure and orientation are as important as overall length.

Send your specification

Parameter Customization
Pitch According to cable and connector specification
Conductor count Project-specific
Cable length Custom length and defined tolerances
Contact orientation Same-side / opposite-side
Exposed contact length According to drawing
Reinforcement Where required
Fold pattern Straight, Z-fold, angled or project-defined
Connector interface ZIF / FPC connector or specified interface
Grounding Where required
Shielding Only with a compatible specified construction
Labels Custom identification
Packaging Project-specific

FFC Folding & Routing Options

Straight Routing

Direct board-to-board or module connections with defined entry and exit positions.

Z-Fold

An offset path where the cable changes level or direction inside a compact enclosure.

Angled Fold

Routing between offset connector positions, with the fold angle and location specified.

Multi-Fold Routing

A project-defined path through complex internal packaging, reviewed for cable suitability.

For applications involving repeated motion, provide the expected bend radius, movement pattern and cycle requirement so a suitable cable construction can be evaluated. Fold options require review; heat-formed or permanently formed processes are not assumed.

FFC Connector & ZIF Compatibility

Cable pitch, conductor count, exposed contact length, reinforcement thickness and contact orientation must match the mating connector specification.

Review ZIF connectors, FPC/FFC board connectors, latch-style connectors, receptacle housings or customer-specified systems by part number. A matching pitch alone does not establish compatibility.

Cable drawingMating connector drawingConfirmed interface

FFC Materials & Construction Options

Conductor

Flat copper conductors, with plating determined by the approved cable specification.

Insulation

Flexible film construction selected for the required temperature and application.

Reinforcement

Stiffener material and thickness at the contact area where required by the interface.

Contact Finish

Tin or another specified finish, according to the selected cable and connector system.

Shielding

Optional shielded construction where project requirements and the approved supply route support it.

How XSD Produces Custom FFC Assemblies

  1. Specification Review

    Review pitch, count, length, contacts, interface, fold pattern, quantity and inspection requirements.

  2. Material / Component Confirmation

    Confirm the FFC construction, approved source and mating connector.

  3. Cable Preparation

    Prepare the cable to the approved dimensional requirements.

  4. Connector / Interface Integration

    Integrate specified connectors or related components where required.

  5. Routing / Folding / Protection

    Apply approved folds, reinforcement, identification or protective features.

  6. Inspection

    Verify dimensions, contact orientation, connector fit and applicable electrical requirements.

XSD’s role is custom assembly and integration. The cable supply route is confirmed per project; this does not imply that all raw FFC is laminated in-house.

Manufacturing Capabilities Supporting FFC Assemblies

The company profile documents wire/cable processing, connector assembly, HDMI soldering, vertical and low-pressure injection molding, electrical testing, dimensional inspection and CCD inspection.

Connector & Interface Assembly

Integration of compatible connector and interface components.

Selected Soldering Processes

Soldered interconnection where required and compatible with the assembly design.

Protective Processing

Molding, reinforcement or dispensing where the FFC design and process permit.

Electrical & Dimensional Inspection

Project-specific checks using available testing and measurement resources.

Selected soldering equipment
Vertical injection molding
Low-pressure injection molding

View Manufacturing Capabilities

FFC Cable Assembly Testing & Inspection

Dimensional Inspection

Overall length, contact exposure, fold positions, reinforcement dimensions and connector position.

Visual Inspection

Conductor/contact condition, surface damage, fold quality, connector fit and reinforcement.

Electrical Inspection

Continuity or circuit verification and DC resistance, where applicable.

Mechanical Inspection

Connector engagement, pull/retention evaluation and bend-related inspection where specified.

CCD inspection
Projection measurement
Circuit testing
DC resistance testing

Inspection follows the approved quality plan. Signal performance depends on conductor geometry, pitch, grounding, shielding, cable length, connector system and electrical interface. High-speed or impedance requirements need a defined construction and validation method.

FFC Cable Assemblies for OEM Applications

Display & HMI Systems

Compact board-to-display connections.

Industrial Electronics

Internal controller and PCB interconnections.

Medical Equipment

Compact device and instrument interconnects, subject to customer qualification.

Consumer Electronics

Thin internal electrical connections.

Printers & Scanners

Space-constrained routing; moving applications require a motion review.

Robotics & Automation

Selected low-profile connections within compact equipment.

Smart Devices

Compact module and interface connections.

FFC Assemblies for Display Connections

FFCs are widely used for low-profile connections between LCD/TFT modules, touch interfaces, driver boards and control electronics. For LVDS, eDP, micro-coax or other display-specific interconnects, explore the broader system-level options.

View Display Cable Assemblies

Why Source Custom FFC Assemblies from XSD?

Build-to-Print Manufacturing

Projects based on drawings, connector specifications, dimensions and approved requirements.

Broader Wire & Cable Background

Experience with multiple flat and flexible cable constructions in XSD’s broader manufacturing business.

Integration Capability

Customer-specified FFC components integrated into compatible connectorized assemblies and larger wiring systems.

Soldering & Protective Processes

Selected soldering, molding and protective operations matched to the design.

Inspection Resources

Electrical, dimensional and mechanical inspection resources.

Prototype to Production

Sample builds, first-article approval and repeat OEM production.

What We Need to Quote Your FFC Cable Assembly

Send the available specifications below. We can identify missing details during the project review.

  • Pitch
  • Conductor count
  • Overall cable length
  • Contact orientation
  • Exposed contact length
  • Conductor / contact finish
  • Reinforcement requirement
  • Connector part number
  • Mating connector information
  • Fold pattern
  • Bend radius, if relevant
  • Dynamic movement requirement
  • Shielding requirement
  • Quantity
  • Application
  • Drawing
  • Sample, if available
  • Inspection requirements

    Your FFC project









    One file up to 10 MB. Combine multiple documents in a ZIP file.

    Frequently Asked Questions

    What information is needed to quote a custom FFC cable?

    Provide pitch, conductor count, overall length, contact orientation, exposed contact length and mating connector part numbers. Include the drawing, quantity, fold pattern, reinforcement and inspection requirements. A sample can help resolve remaining details.

    What is the difference between FFC and ribbon cable?

    FFC uses flat conductors laminated within flexible insulation. Conventional ribbon cable uses individually insulated round conductors arranged side by side. Their contact systems and termination methods differ; the names are not interchangeable.

    What is the difference between FFC and FPC?

    FFC generally has parallel flat conductors. FPC uses printed circuit traces on a flexible substrate and can include routed circuit patterns. Integrating an FPC component is separate from fabricating the flexible circuit itself.

    Can XSD manufacture same-side and opposite-side contact FFCs?

    Both orientations can be reviewed for a custom assembly. Confirm the exposed contact faces on the drawing and provide the mating connector details. Supplier Type A and Type B naming alone is not a sufficient production specification.

    Can FFC length and conductor count be customized?

    Custom length and conductor count can be reviewed against the selected cable construction and connector. The approved drawing establishes dimensions, tolerances and measurement reference points. Available combinations are confirmed during quotation.

    Can XSD integrate ZIF-compatible FFC cables?

    Yes, for a confirmed compatible cable and connector system. Pitch, circuit count, contact exposure, reinforced thickness and contact position must match the mating connector drawing. Compatibility is evaluated for the specified part number.

    Can FFC cables be folded for compact routing?

    Straight, Z-fold, angled and multi-fold layouts can be reviewed. Supply fold locations, routing space and bend requirements. Repeated-motion applications need a defined movement pattern and cycle requirement before selecting the cable construction.

    Can XSD manufacture from an existing sample?

    A sample can support dimensional and interface review. We also need confirmation of hidden requirements such as material, contact finish, circuit assignment and acceptance criteria. Production follows the agreed drawing and specification.

    What testing is available for FFC cable assemblies?

    Inspection can include dimensional verification, visual inspection, continuity or circuit verification, and DC resistance where applicable. Connector engagement, retention and bend-related checks are included when specified in the approved quality plan.

    Do you support prototypes before production?

    Prototype and first-article builds can be reviewed before repeat production. Component availability, quantity, tooling, lead time and acceptance requirements are agreed during quotation; no universal minimum order or lead time is assumed.

    Start Your FFC Cable Assembly Project

    Send your pitch, conductor count, contact orientation, length and interface requirements. XSD will review the assembly, routing and inspection needs for your application.

    Upload Your FFC Drawing & Get a Quote