CUSTOM INTERCONNECTS · DEFINED REQUIREMENTS

Custom RF
Cable Assemblies

XSD Harness manufactures custom RF cable assemblies according to customer-approved cable specifications, connector part numbers, lengths and electrical requirements. Our manufacturing capabilities include cable preparation, termination, soldering, connector assembly, protective processing and project-specific inspection.

Build-to-PrintCustom LengthsRF Connector IntegrationOEM Production

Manufacturing to your specification. High-frequency validation requirements are confirmed during project review.

FINISHED INTERCONNECTSREAL XSD PHOTOGRAPHS
Small coax assembly example
Mixed-interface coax assembly example

Connector families, impedance and frequency ratings require part-number verification. Photos are not RF test evidence.

ENGINEERING START POINT

Request an RF Assembly Quote

Send your cable and connector specification. Include RF acceptance requirements where applicable.











    One file up to 10 MB. For multiple documents, upload a ZIP file.

    Standard RFQs are typically reviewed within 1–3 business days.

    THE COMPLETE SIGNAL PATH

    What Is an RF Cable Assembly?

    An RF cable assembly combines a high-frequency cable with specified RF connectors and termination components to transmit radio-frequency or high-frequency electrical signals between devices, modules or antennas.

    Unlike a basic low-frequency connection, RF performance depends on the complete interconnect system: cable construction, impedance, connector selection, termination quality, shielding and cable length. XSD manufactures to customer-defined specifications rather than treating all RF assemblies as one standard product.

    You specify. XSD reviews and builds.

    You specify: cable, connector, impedance, length, shielding, protection, quantity and inspection requirements.

    XSD builds: the approved preparation, termination, connector assembly and protective processing route, followed by the agreed inspection.

    This page focuses on RF electrical requirements. Broader coax construction requests can be discussed through the Coax Cable Assembly enquiry route.

    CONFIGURE THE INTERCONNECT

    Custom RF Cable Assembly Options

    Control the cable and both interfaces together. Ratings belong to the specified system, not to a generic RF product label.

    Cable Type
    Customer-specified coaxial or other high-frequency construction, with cable part number and applicable documentation.
    Connector Type
    Project-defined RF family and manufacturer part number, including mating interface and gender.
    Impedance
    Application-defined nominal impedance, such as 50 Ω or 75 Ω where applicable to the chosen system.
    Cable Length
    Overall length, tolerance, reference planes and stripped dimensions according to the drawing.
    Shielding
    Braid, foil or combined construction and termination details determined by the selected cable specification.
    Jacket / Protection
    Heat shrink, sleeving, labels or compatible molded strain relief where required.
    Connector Orientation
    Straight or right-angle options only where supported by the selected connector and routing design.
    Assembly Identification
    Customer part numbers, labels, circuit identification and packaging marks as specified.

    INTERFACES TO REVIEW

    Common RF Cable Assembly Configurations

    The interface combinations below are enquiry categories, not a verified catalogue or a promise of stock availability. Exact sourcing and assembly feasibility must be confirmed.

    Requested configuration Typical project context Review before commitment
    SMA to SMA RF modules, antennas, test equipment and electronic systems. Confirm exact interfaces, cable and termination method.
    SMA to BNC Connections between equipment using different RF interfaces. Verify impedance, gender and mating components at both ends.
    BNC to BNC Instrumentation, video and signal interconnections. Define the actual operating requirement rather than assuming all BNC systems match.
    N-Type Cable Assemblies Selected industrial, antenna and communication systems. Confirm the complete connector/cable specification and tooling route.
    MCX / MMCX Assemblies Compact electronic and embedded interconnections. Review component handling, space and termination compatibility.
    Automotive RF Assemblies Selected telematics, antennas, camera or vehicle electronics projects. Customer-specified automotive interfaces; no unverified Fakra/HSD approval or family availability claim.

    A request for a named family is subject to confirmation. Electrical ratings, sealing and frequency limits must come from the exact cable/connector documentation and the agreed validation plan.

    A CONTROLLED ASSEMBLY ROUTE

    How XSD Manufactures RF Cable Assemblies

    The manufacturing route follows the approved cable and connector system. Processes and setup are selected for the actual termination design.

    1. Cable Preparation

      Cutting, stripping and jacket preparation follow specified dimensions and reference points. Avoid damaging the conductor, dielectric or shield during preparation.

    2. Shield Preparation

      Braid or foil preparation follows the cable and connector termination method, with controlled exposure and positioning.

    3. Center Conductor Termination

      Crimped, soldered or other specified methods follow the selected contact and cable requirements.

    4. Connector Assembly

      Connector body, contact and associated components are assembled according to approved documentation.

    5. Strain Relief & Protection

      Heat shrink, sleeves, compatible molding and labels are added where the product design requires them.

    6. Inspection

      Visual, dimensional and agreed electrical checks follow the approved inspection plan. RF-specific validation is addressed separately.

    Cable / wire cutting equipment · documented general resource
    Terminal processing equipment · suitability reviewed per contact
    Vertical molding equipment · selected compatible assemblies
    HDMI soldering equipment in the company profile

    CONTACT + CABLE + PROCESS

    RF Connector Termination & Soldering

    Depending on the selected connector and cable system, RF assemblies may require crimped, soldered or hybrid termination methods. XSD supports selected soldering and connector assembly operations based on customer-approved specifications and component requirements.

    Review center-conductor preparation, dielectric exposure, shield termination and connector installation instructions as a connected process. Termination quality cannot be reduced to a single soldering claim or an attractive finished photograph.

    The profile documents HDMI soldering equipment. It does not establish a fully automated RF connector termination line. Dedicated RF tooling and process suitability must be confirmed for the requested components.

    DEFINE PERFORMANCE BEFORE PRODUCTION

    Electrical Requirements for RF Cable Assemblies

    Specify how the assembly must perform, how it will be measured and what constitutes acceptance.

    Impedance & frequency

    Identify characteristic impedance and operating frequency or frequency band. Do not infer frequency capability from connector appearance.

    Insertion loss

    State any permitted attenuation, relevant frequencies and measurement conditions. Cable type and length contribute to the requirement.

    Return loss / VSWR

    Specify acceptance limits and test conditions where applicable. These are RF measurements, not a substitute for continuity checks.

    Shielding & length

    Define cable shield construction, termination, finished length and reference points together.

    Connector interface

    Identify both mating interfaces, gender, orientation and exact component part numbers.

    Power & environment

    State relevant power level, temperature, routing, moisture and mechanical conditions for project review.

    XSD manufactures assemblies to customer-defined RF specifications. Where insertion loss, return loss, VSWR or S-parameter measurement is required, the test method, acceptance criteria and validation route must be confirmed during project review.

    TWO DIFFERENT LEVELS OF VERIFICATION

    RF Cable Assembly Testing & Inspection

    General electrical and mechanical inspection does not establish high-frequency performance. Keep the manufacturing checks and RF validation plan distinct.

    DOCUMENTED COMPANY RESOURCES

    In-House Inspection Resources

    • DC resistance testing
    • Wire / cable harness testing
    • CCD inspection
    • Dimensional measurement
    • Tensile testing
    • Plug / pull testing

    Methods, sampling and acceptance criteria follow the approved drawing and inspection plan. Equipment does not imply every test applies to every assembly.

    PROJECT-SPECIFIC · CONFIRM BEFORE ORDER

    RF Validation Requirements

    • Continuity / circuit requirements as specified
    • Impedance verification
    • Insertion loss
    • Return loss
    • VSWR
    • S-parameters

    Required equipment, fixtures, method, frequency range and acceptance limits need confirmation. Neither in-house VNA/TDR equipment nor an external laboratory route is asserted without documentation.

    Wire harness tester
    DC resistance tester
    CCD inspection equipment
    Projection measurement equipment
    Tensile testing equipment
    Plug / pull testing equipment

    Continuity or DC resistance results alone do not verify impedance, insertion loss, return loss or VSWR. Agree the required high-frequency validation before committing to a performance specification.

    View testing & inspection resources →

    CONSTRUCTION FOLLOWS THE SPECIFICATION

    Cable & Material Options

    Coaxial Cable

    Customer-specified RF coax construction, identified by part number and relevant technical documentation.

    Shielded Signal Cable

    Selected electronic and communication applications with an agreed shield termination method.

    Flexible Cable

    Routing-sensitive or compact installations, subject to the cable’s bend and service requirements.

    High-Temperature Cable

    Appropriate insulation systems where the actual application requires them.

    Custom Constructions

    Reviewed through the broader wire and cable manufacturing resources of Dongguan XSD Cable Technology Co., Ltd.

    Broader XSD wire and cable manufacturing background
    Bending test equipment · project-dependent general mechanical inspection

    From cable construction to the finished interconnect

    Define conductor, dielectric, shield and jacket requirements through the selected cable specification. Cable flexibility, environment and routing matter alongside electrical inputs.

    For broader coax construction, general signal or video requests, use the coax assembly enquiry route. For display interfaces, use the display cable assembly enquiry route. These are related but distinct from this page’s RF-performance focus.

    OEM USE CASES

    RF Cable Assemblies for OEM Applications

    Each application is reviewed against its selected cable, connectors and performance criteria. No sector-specific certification or approval is implied.

    Industrial Equipment

    Signal and antenna connections in machinery, instrumentation and associated equipment.

    Explore industry →

    Communication Equipment

    RF interconnects between modules, antennas and communication systems.

    Explore industry →

    Automotive Electronics

    Selected telematics, camera, antenna and vehicle communication applications.

    Explore industry →

    Medical Equipment

    RF or high-frequency interconnects for specified diagnostic and electronic equipment.

    Explore industry →

    Robotics & Automation

    Sensor and communication interconnections in automated equipment, with routing conditions defined.

    Explore industry →

    Electronic Equipment

    Module-to-module and board-to-device connections using the specified RF interfaces.

    Explore industry →

    MANUFACTURING EVIDENCE, NOT UNVERIFIED RATINGS

    Why Source RF Cable Assemblies from XSD?

    About XSD →

    Cable Manufacturing Background

    The broader company manufactures wires and cables as well as finished assemblies.

    Build-to-Print Production

    Manufacturing follows customer drawings, cable specifications and connector part numbers.

    Flexible Termination Methods

    Selected crimping, soldering and connector assembly processes follow the approved component system.

    Inspection Resources

    Documented general electrical, dimensional and mechanical equipment supports the inspection plan.

    Prototype to Production

    Samples and production quantities are reviewed according to component availability and complexity.

    OEM Industry Experience

    The wider business serves electronics, automotive, industrial equipment, robotics and energy applications.

    FROM REQUIREMENT REVIEW TO SHIPMENT

    Your Custom RF Assembly Project

    Requirements Review

    Review drawing, BOM, RF inputs, interfaces and quantity. Resolve missing component information.

    Manufacturing Review

    Confirm preparation, termination, protection and inspection routes, including validation responsibilities.

    Prototype / First Article

    Build agreed samples where required before production release. Schedules remain project-specific.

    Production Assembly

    Use approved materials and the released assembly requirements after customer approval.

    Inspection & Delivery

    Complete agreed checks, identification, packaging and shipment requirements.

    No fixed sample turnaround, universal MOQ, blanket RF certification or customer testimonial is substituted for project evidence.

    PREPARE AN ACTIONABLE ENQUIRY

    What We Need to Quote Your RF Cable Assembly

    Send as much of the approved specification as available. Identify unresolved items so the review can separate manufacturing questions from RF validation requirements.

    Upload RF Cable Drawing or BOM

    ENGINEERING & PROCUREMENT QUESTIONS

    Frequently Asked Questions

    Can XSD manufacture 50-ohm and 75-ohm RF cable assemblies?

    A project can be reviewed when the specified cable and connector system is designed for the required impedance. Confirm the exact components, operating frequency and acceptance criteria during engineering review. A nominal impedance value does not establish a frequency rating or a measured result.

    What RF connectors can you assemble?

    Provide the connector family, manufacturer part number, interface, gender and orientation. The supplied photographs show connectorized coax examples, but they do not establish an approved catalogue of RF families. Sourcing, tooling and assembly compatibility are confirmed for each project before commitment.

    Can you manufacture custom cable lengths?

    Yes, according to approved drawings and cable preparation requirements. State the measurement reference points, tolerance, stripped dimensions and required bend or routing conditions. If phase or delay matters, specify that separately rather than assuming a mechanical length controls every RF characteristic.

    Do you provide SMA, BNC or N-type cable assemblies?

    These interface requests are reviewed against the selected cable, connector part numbers, tooling and component availability. They are not presented here as a verified stock range. Send the complete requirement so XSD can confirm whether the requested configuration can be manufactured and validated.

    Can RF assemblies be overmolded?

    Selected designs can incorporate compatible molded protection or strain relief after engineering review. Connector geometry, cable jacket, material and process conditions must be considered. Do not assume molding preserves a particular RF or environmental performance without design-specific validation.

    Can you test insertion loss or VSWR?

    These are project-specific high-frequency requirements. The required method, frequency range, fixture or reference planes, acceptance criteria and available validation route must be confirmed during project review. The supplied company profile does not establish in-house VNA or TDR capability.

    Can you manufacture from an existing sample?

    A physical sample can support review, subject to component identification and technical clarification. Confirm cable and connector part numbers, length references, impedance, operating frequency and required inspection. Appearance alone cannot establish cable construction or high-frequency performance.

    Do you support prototypes?

    Development samples and first articles can be reviewed depending on component availability, tooling and project complexity. Technical requirements and validation responsibilities should be agreed before samples are released. Prototype quantities and schedules are confirmed for the individual project.

    DRAWING + BOM + RF SPECIFICATION

    Start Your RF Cable Assembly Project

    XSD manufactures custom RF assemblies to agreed cable, connector, length and inspection requirements. Start with the specification your equipment needs.

    Upload Drawing & Get a Quote

    Specific RF performance and the required validation route are confirmed before commitment.

    Enlarged supplied company photograph