Impedance & frequency
Identify characteristic impedance and operating frequency or frequency band. Do not infer frequency capability from connector appearance.
CUSTOM INTERCONNECTS · DEFINED REQUIREMENTS
XSD Harness manufactures custom RF cable assemblies according to customer-approved cable specifications, connector part numbers, lengths and electrical requirements. Our manufacturing capabilities include cable preparation, termination, soldering, connector assembly, protective processing and project-specific inspection.
Manufacturing to your specification. High-frequency validation requirements are confirmed during project review.
Connector families, impedance and frequency ratings require part-number verification. Photos are not RF test evidence.
ENGINEERING START POINT
Send your cable and connector specification. Include RF acceptance requirements where applicable.
THE COMPLETE SIGNAL PATH
An RF cable assembly combines a high-frequency cable with specified RF connectors and termination components to transmit radio-frequency or high-frequency electrical signals between devices, modules or antennas.
Unlike a basic low-frequency connection, RF performance depends on the complete interconnect system: cable construction, impedance, connector selection, termination quality, shielding and cable length. XSD manufactures to customer-defined specifications rather than treating all RF assemblies as one standard product.
You specify: cable, connector, impedance, length, shielding, protection, quantity and inspection requirements.
XSD builds: the approved preparation, termination, connector assembly and protective processing route, followed by the agreed inspection.
This page focuses on RF electrical requirements. Broader coax construction requests can be discussed through the Coax Cable Assembly enquiry route.
CONFIGURE THE INTERCONNECT
Control the cable and both interfaces together. Ratings belong to the specified system, not to a generic RF product label.
INTERFACES TO REVIEW
The interface combinations below are enquiry categories, not a verified catalogue or a promise of stock availability. Exact sourcing and assembly feasibility must be confirmed.
| Requested configuration | Typical project context | Review before commitment |
|---|---|---|
| SMA to SMA | RF modules, antennas, test equipment and electronic systems. | Confirm exact interfaces, cable and termination method. |
| SMA to BNC | Connections between equipment using different RF interfaces. | Verify impedance, gender and mating components at both ends. |
| BNC to BNC | Instrumentation, video and signal interconnections. | Define the actual operating requirement rather than assuming all BNC systems match. |
| N-Type Cable Assemblies | Selected industrial, antenna and communication systems. | Confirm the complete connector/cable specification and tooling route. |
| MCX / MMCX Assemblies | Compact electronic and embedded interconnections. | Review component handling, space and termination compatibility. |
| Automotive RF Assemblies | Selected telematics, antennas, camera or vehicle electronics projects. | Customer-specified automotive interfaces; no unverified Fakra/HSD approval or family availability claim. |
A request for a named family is subject to confirmation. Electrical ratings, sealing and frequency limits must come from the exact cable/connector documentation and the agreed validation plan.
A CONTROLLED ASSEMBLY ROUTE
The manufacturing route follows the approved cable and connector system. Processes and setup are selected for the actual termination design.
Cutting, stripping and jacket preparation follow specified dimensions and reference points. Avoid damaging the conductor, dielectric or shield during preparation.
Braid or foil preparation follows the cable and connector termination method, with controlled exposure and positioning.
Crimped, soldered or other specified methods follow the selected contact and cable requirements.
Connector body, contact and associated components are assembled according to approved documentation.
Heat shrink, sleeves, compatible molding and labels are added where the product design requires them.
Visual, dimensional and agreed electrical checks follow the approved inspection plan. RF-specific validation is addressed separately.
CONTACT + CABLE + PROCESS
Depending on the selected connector and cable system, RF assemblies may require crimped, soldered or hybrid termination methods. XSD supports selected soldering and connector assembly operations based on customer-approved specifications and component requirements.
Review center-conductor preparation, dielectric exposure, shield termination and connector installation instructions as a connected process. Termination quality cannot be reduced to a single soldering claim or an attractive finished photograph.
The profile documents HDMI soldering equipment. It does not establish a fully automated RF connector termination line. Dedicated RF tooling and process suitability must be confirmed for the requested components.
DEFINE PERFORMANCE BEFORE PRODUCTION
Specify how the assembly must perform, how it will be measured and what constitutes acceptance.
Identify characteristic impedance and operating frequency or frequency band. Do not infer frequency capability from connector appearance.
State any permitted attenuation, relevant frequencies and measurement conditions. Cable type and length contribute to the requirement.
Specify acceptance limits and test conditions where applicable. These are RF measurements, not a substitute for continuity checks.
Define cable shield construction, termination, finished length and reference points together.
Identify both mating interfaces, gender, orientation and exact component part numbers.
State relevant power level, temperature, routing, moisture and mechanical conditions for project review.
XSD manufactures assemblies to customer-defined RF specifications. Where insertion loss, return loss, VSWR or S-parameter measurement is required, the test method, acceptance criteria and validation route must be confirmed during project review.
TWO DIFFERENT LEVELS OF VERIFICATION
General electrical and mechanical inspection does not establish high-frequency performance. Keep the manufacturing checks and RF validation plan distinct.
DOCUMENTED COMPANY RESOURCES
Methods, sampling and acceptance criteria follow the approved drawing and inspection plan. Equipment does not imply every test applies to every assembly.
PROJECT-SPECIFIC · CONFIRM BEFORE ORDER
Required equipment, fixtures, method, frequency range and acceptance limits need confirmation. Neither in-house VNA/TDR equipment nor an external laboratory route is asserted without documentation.
Continuity or DC resistance results alone do not verify impedance, insertion loss, return loss or VSWR. Agree the required high-frequency validation before committing to a performance specification.
CONSTRUCTION FOLLOWS THE SPECIFICATION
Customer-specified RF coax construction, identified by part number and relevant technical documentation.
Selected electronic and communication applications with an agreed shield termination method.
Routing-sensitive or compact installations, subject to the cable’s bend and service requirements.
Appropriate insulation systems where the actual application requires them.
Reviewed through the broader wire and cable manufacturing resources of Dongguan XSD Cable Technology Co., Ltd.
Define conductor, dielectric, shield and jacket requirements through the selected cable specification. Cable flexibility, environment and routing matter alongside electrical inputs.
For broader coax construction, general signal or video requests, use the coax assembly enquiry route. For display interfaces, use the display cable assembly enquiry route. These are related but distinct from this page’s RF-performance focus.
OEM USE CASES
Each application is reviewed against its selected cable, connectors and performance criteria. No sector-specific certification or approval is implied.
Signal and antenna connections in machinery, instrumentation and associated equipment.
RF interconnects between modules, antennas and communication systems.
Selected telematics, camera, antenna and vehicle communication applications.
RF or high-frequency interconnects for specified diagnostic and electronic equipment.
Sensor and communication interconnections in automated equipment, with routing conditions defined.
Module-to-module and board-to-device connections using the specified RF interfaces.
The broader company manufactures wires and cables as well as finished assemblies.
Manufacturing follows customer drawings, cable specifications and connector part numbers.
Selected crimping, soldering and connector assembly processes follow the approved component system.
Documented general electrical, dimensional and mechanical equipment supports the inspection plan.
Samples and production quantities are reviewed according to component availability and complexity.
The wider business serves electronics, automotive, industrial equipment, robotics and energy applications.
FROM REQUIREMENT REVIEW TO SHIPMENT
Review drawing, BOM, RF inputs, interfaces and quantity. Resolve missing component information.
Confirm preparation, termination, protection and inspection routes, including validation responsibilities.
Build agreed samples where required before production release. Schedules remain project-specific.
Use approved materials and the released assembly requirements after customer approval.
Complete agreed checks, identification, packaging and shipment requirements.
No fixed sample turnaround, universal MOQ, blanket RF certification or customer testimonial is substituted for project evidence.
PREPARE AN ACTIONABLE ENQUIRY
Send as much of the approved specification as available. Identify unresolved items so the review can separate manufacturing questions from RF validation requirements.
ENGINEERING & PROCUREMENT QUESTIONS
A project can be reviewed when the specified cable and connector system is designed for the required impedance. Confirm the exact components, operating frequency and acceptance criteria during engineering review. A nominal impedance value does not establish a frequency rating or a measured result.
Provide the connector family, manufacturer part number, interface, gender and orientation. The supplied photographs show connectorized coax examples, but they do not establish an approved catalogue of RF families. Sourcing, tooling and assembly compatibility are confirmed for each project before commitment.
Yes, according to approved drawings and cable preparation requirements. State the measurement reference points, tolerance, stripped dimensions and required bend or routing conditions. If phase or delay matters, specify that separately rather than assuming a mechanical length controls every RF characteristic.
These interface requests are reviewed against the selected cable, connector part numbers, tooling and component availability. They are not presented here as a verified stock range. Send the complete requirement so XSD can confirm whether the requested configuration can be manufactured and validated.
Selected designs can incorporate compatible molded protection or strain relief after engineering review. Connector geometry, cable jacket, material and process conditions must be considered. Do not assume molding preserves a particular RF or environmental performance without design-specific validation.
These are project-specific high-frequency requirements. The required method, frequency range, fixture or reference planes, acceptance criteria and available validation route must be confirmed during project review. The supplied company profile does not establish in-house VNA or TDR capability.
A physical sample can support review, subject to component identification and technical clarification. Confirm cable and connector part numbers, length references, impedance, operating frequency and required inspection. Appearance alone cannot establish cable construction or high-frequency performance.
Development samples and first articles can be reviewed depending on component availability, tooling and project complexity. Technical requirements and validation responsibilities should be agreed before samples are released. Prototype quantities and schedules are confirmed for the individual project.
DRAWING + BOM + RF SPECIFICATION
XSD manufactures custom RF assemblies to agreed cable, connector, length and inspection requirements. Start with the specification your equipment needs.
Specific RF performance and the required validation route are confirmed before commitment.