Connector specification
Customer-defined Molex connector family, housing part number, circuit count and mating interface. Confirm keying, orientation and any required locking features.
CUSTOMER-SPECIFIED CONNECTOR SYSTEMS
XSD Harness manufactures custom cable assemblies using specified Molex connector systems, wires, terminals and protective components according to customer drawings, BOMs and pinout requirements.
Independent assembly manufacturing. Connector part numbers and sourcing follow the approved BOM.
Photos illustrate finished construction. Exact Molex series, housing and terminal part numbers require BOM confirmation.
THE COMPLETE INTERCONNECTION
A Molex cable assembly combines a Molex connector system with specified wires or cables, terminals, contacts and protective components to create a finished electrical interconnection.
The assembly may carry power, signals, control circuits or a combination of functions, depending on the selected connector family and application. XSD manufactures these assemblies according to customer-approved connector part numbers, pin assignments, wire specifications, lengths and inspection requirements.
For an OEM buyer, the key deliverable is the complete assembly that fits the equipment and connects the correct circuits. Confirm the mating interface and connector-to-wire compatibility before treating two similar-looking housings as equivalent.
DRAWING + BOM + PINOUT
Define the electrical interfaces and assembly details before production. Each choice must work with the selected connector system.
Customer-defined Molex connector family, housing part number, circuit count and mating interface. Confirm keying, orientation and any required locking features.
Specify the terminal or contact matched to the conductor and connector system. Wire size, insulation diameter and contact requirements govern the approved combination.
Define AWG, conductor construction, insulation, color and cable construction. Material selection follows the application and component documentation.
Specify circuit positions and wiring sequence, including the viewing direction of the connector drawing. Identify unused cavities and any special circuit checks.
Control overall length, branch lengths, strip dimensions and the measurement reference points. State tolerances instead of relying on a photograph.
Select heat shrink, sleeving, tubing, tape, labels or molded strain relief where required. Seals, clips, ferrites, markings and cable glands are reviewed against the BOM and available process.
OEM APPLICATIONS
Connector families and assembly requirements vary by equipment. Application review does not imply a universal electrical rating or sector-specific approval.
Power, control and signal connections within machinery and automation systems.
Connectorized assemblies for selected vehicle and equipment electrical systems.
Custom electrical interconnections for diagnostic and equipment applications, to approved requirements.
Sensor, actuator, encoder, motor and control wiring. Routing and movement requirements need project review.
Internal power and signal interconnections in battery and control systems.
Board-to-wire and device interconnections for electronic products.
CONTROLLED MANUFACTURING
XSD connects the approved drawing and BOM to a manufacturing route for the complete connector cable assembly.
Cutting and stripping follow approved dimensions. Wire identification and conductor preparation support the specified termination process.
Automatic or semi-automatic equipment processes terminals based on the selected wire and contact. Setup follows the approved component combination.
Crimp quality is evaluated against the inspection plan. Required checks can include cross-section analysis and pull-force testing.
Terminated wires are inserted into specified connector cavities according to the approved pinout. Circuit identity and terminal retention requirements guide assembly.
Sleeving, tubing, heat shrink, labels, ties or molding are added where required. Branch routing and protection follow the product design.
Finished assemblies are checked against project-specific electrical and dimensional requirements before final release.
WIRE → TERMINAL → HOUSING
Crimping requirements depend on the selected terminal and conductor combination. XSD uses automatic and semi-automatic terminal processing equipment and can incorporate pull-force testing and cross-section analysis into the inspection process where required by the project specification.
Review conductor size, insulation diameter, terminal part number and the relevant application specification together. A connector housing alone does not define a suitable crimp. Tooling suitability and acceptance criteria must be agreed for the actual assembly.
WIRE & CABLE MANUFACTURING BACKGROUND
XSD’s broader wire and cable manufacturing background supports material discussions beyond the connector housing. Final construction follows the approved project specification.
Individual conductors for specified power or signal circuits, with the required gauge, color and insulation.
Grouped electrical circuits with defined core count, jacket requirements and conductor identification.
Selected signal and interference-sensitive applications, including an agreed shield termination method.
Appropriate insulation systems where the application’s temperature requirement justifies their selection.
Customer-specified automotive wire types and applicable material requirements for the intended equipment.
Project-specific cable requirements reviewed against broader XSD cable manufacturing capability.
Wire selection is not a blanket current, voltage, temperature or certification claim. Connector and wire documentation must support the complete design.
PROTECTION DESIGNED INTO THE ASSEMBLY
Depending on the product design, Molex-based cable assemblies can incorporate heat shrink, sleeving, tubing, tape, labels or molded protection. XSD’s documented manufacturing equipment includes vertical injection molding and low-pressure injection molding machines for selected cable assembly applications.
Review the housing geometry, material compatibility, tooling and service conditions before specifying molding. No IP67 or IP68 rating is assumed for an unvalidated assembly.
INSPECTION MATCHED TO THE DRAWING
Inspection methods are selected according to the approved drawing, connector specification and customer quality requirements. Not every assembly requires every listed inspection method.
Wire sequence / circuit verification, DC resistance testing and harness electrical testing support the defined circuit requirements.
Terminal cross-section analysis and tensile / pull-force testing evaluate specified termination characteristics.
CCD inspection and projection measurement may support appearance, positioning and dimensional checks under the inspection plan.
Acceptance criteria, sampling and records are established for the project. Equipment availability does not mean every method applies to every order.
SPECIFY BOTH ENDS
These are configuration options for engineering review, not a claim that every connector combination is interchangeable or available from stock.
Connectorized assembly with specified Molex connectors at both ends. Define the cavity-to-cavity wiring map and mating interfaces.
Molex connector at one end and stripped, tinned or terminated conductors at the other. Specify end preparation and identification.
Connectorized cable with ring terminals for equipment or power connections. Ring geometry, conductor compatibility and insulation requirements follow the drawing.
Mixed-brand interconnect using customer-specified connectors. Each end uses its own approved contacts and mating components.
Cable assemblies for board-to-wire applications. Confirm the board-side header part number, orientation and connection requirements.
Multiple specified connectors integrated into a branched wiring assembly. Define branch lengths, routing and circuit assignments.
For a complex multi-branch project, include the full harness layout and branch schedule. Review wire harness manufacturing capabilities alongside the broader Custom Cable Assembly page.
APPROVAL BEFORE REPEAT PRODUCTION
Resolve component identification, pinout, tooling and inspection questions before production release. Samples establish an agreed reference for subsequent builds. Lead times, sample quantities and production schedules are project-specific and confirmed during quotation.
MANUFACTURING EVIDENCE
Manufacturing follows customer-approved drawings, BOMs and connector part numbers rather than assumptions based on appearance.
Access to broader wire and cable manufacturing expertise supports construction and material discussions.
Cutting, stripping, crimping, insertion, soldering and selected molding processes support the agreed manufacturing route.
Electrical, dimensional and mechanical inspection equipment supports project-defined acceptance requirements.
Development builds and production orders follow the agreed technical approvals and controlled specification.
The broader company serves customers across international markets. Requirements and documentation are agreed for the specific OEM program.
PROJECT QUESTIONS
Yes. Provide the housing, terminal and mating-component part numbers with your drawing and BOM. XSD reviews the complete connector-to-wire combination and manufacturing requirements before quotation. Component availability and the approved sourcing route are confirmed for each project.
Mixed-brand configurations can be reviewed when the connectors, terminals and pin assignments are specified. Each end must be compatible with its own conductor and mating interface. Brands do not imply interchangeability, and substitutions require customer approval.
Send the drawing or sample, BOM, connector and terminal part numbers, pinout, wire specifications, lengths, order quantity and inspection requirements. Include any protection, labeling, packaging or documentation needs. If information is incomplete, identify which items need engineering clarification.
Yes, within the selected connector and terminal system’s requirements. Specify conductor size, insulation diameter, overall and branch lengths, cavity assignments and tolerances. A different wire gauge can require a different terminal, tooling setup or inspection plan.
Selected assemblies can incorporate molded protection using documented vertical and low-pressure molding equipment. Feasibility depends on the connector geometry, materials, tooling and application. Environmental or ingress ratings must be validated for the finished design rather than assumed.
Available resources include circuit and wire-sequence verification, DC resistance and harness electrical testing, terminal cross-section analysis, tensile testing and CCD inspection. Projection measurement may be included where required. The approved inspection plan determines which methods apply.
A physical sample can support engineering review, but it does not automatically identify every material or connector part number. Confirm the BOM, mating interface, pinout, dimensions and acceptance criteria before production. Destructive evaluation, if needed, requires agreement.
Yes. Development samples or first articles can be reviewed before repeat production. The project moves forward after the agreed technical and quality approvals. Sample quantities, tooling needs and schedules are established for the actual assembly, not promised as a fixed lead time.
Trademark notice. Molex is a trademark of Molex, LLC. XSD Harness is an independent cable assembly manufacturer and is not affiliated with or endorsed by Molex unless otherwise stated. Connector brands are referenced solely to describe customer-specified components used in custom assemblies.
SEND YOUR DRAWING / BOM
Tell us which connector system your equipment requires. Share the approved part numbers and assembly information so XSD can review the complete manufacturing requirement.
A sample or incomplete drawing is a starting point for clarification, not a substitute for confirmed production requirements.